Alinco EJ-41U Instrukcja Obsługi Pobierz pdf (Strona 18)

5. Basic Operation

CTCSS / DCS setting

Many repeaters require a CTCSS tone or a DCS code encode setting as a “key” to access the

system, so-called “selective-calling”. Sometimes, CTCSS or DCS decode features are used on the

output of a repeater so they can be used as a squelch. In this mode, regardless of the main squelch

status, the audio can be heard ONLY when the matching tone/code signal is received. The combi-

nation of CTCSS squelch and DCS function is not available; only one or the other may be used for

a given memory channel.

1. Press TS/DCS key. The current setting will be

displayed with T/SQ/DCS icons and relative

frequency/code. Press the same key to select

T/SQ/DCS setting.

2. The numbers (such as 88.5) represent the CTCSS frequency in Hz. When it is dis-

played with the T icon only, the unit transmits the sub-audible tone while the PTT is

pressed (encode) and the repeater access is enabled (assuming the repeater is using

88.5).

3. Press the same key again so that the SQ icon shows up on the display. This is the

CTCSS decode frequency. This enables CTCSS squelch (or Tone Squelch, TSQ).

4. Press it again so that the 3-digit number and DCS icon is displayed. This is the DCS

code, and it enables DCS encoding and decoding.

88.5

T/SQ

88.5

DCS

023

The original status

For 2 - 4, rotate the main dial or press the UP/DOWN keys to change tone or code. Press any key

(Except TS/DCS, UP/DOWN keys) to enter the setting and return to original status. The T/SQ/

DCS icon will remain on the display to show the current status. To exit, simply use the TS/DCS key

and press it until the relative status icon T/TQ/DCS disappears.

The CTCSS encoding and decoding frequencies may be set differently. The encode setting fre-

quency automatically relates to the decode setting, but decode setting does not affect encode. The

standard set of 39 different CTCSS tones are available as shown on the chart below. DCS encode/

decode cannot be separated and are selectable from 104 codes as shown below.

NOTE: Depending on the deviation level of the incoming DCS coded-signal, your radio may not open the DCS

squelch. If this occurs, return to DCS setting mode and press the CALL key. A decimal point appears on

the 10 MHz order; then set the desired code. This setting can also be stored in a memory channel.

023 025 026 031 032 036 043 047 051 053 054

065 071 072 073 074 114 115 116 122 125 131

132 134 143 145 152 155 156 162 165 172 174

205 212 223 225 226 243 244 245 246 251 252

255 261 263 265 266 271 274 306 311 315 325

331 332 343 346 351 356 364 365 371 411 412

413 423 431 432 445 446 452 454 455 462 464

465 466 503 506 516 523 526 532 546 565 606

612 624 627 631 632 654 662 664 703 712 723

731 732 734 743 754

DCS Codes

67.0 69.3 71.9 74.4 77.0 79.7

82.5 85.4 88.5 91.5 94.8 97.4

100.0 103.5 107.2 110.9 114.8 118.8

123.0 127.3 131.8 136.5 141.3 146.2

151.4 156.7 162.2 167.9 173.8 179.9

186.2 192.8 203.5 210.7 218.1 225.7

233.6 241.8 250.3

CTCSS Tone Frequency(Hz)

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 46 47

Komentarze do niniejszej Instrukcji

Brak uwag

Alinco EJ-41U Instrukcja Obsługi Strona 18

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zdalne sterowanie Alinco EJ-41U